Skip to content

Troubleshooting

Find your symptom below. Most problems are a tap turned off, a flat timer battery, or a setting doing what it was asked.

  • Are you on your home Wi-Fi? The app’s home address only works on your home network. Turn off mobile data briefly to check, or use the Groundsman cloud when away. See My garden portal.
  • Is the controller powered? Check the controller box is plugged in and its power is on.
  • Did the router restart? Give everything a few minutes, then try again.
  • Still nothing? Contact your installer, or Groundsman if you set it up yourself. If the controller is running, your programs carry on even when you can’t open the app.
  1. Look for an alert at the top of Home. It says what happened and what to check.
  2. Tap History on the zone. Was the run skipped (and why), didn’t start, or cut short? See Run history.
  3. Tap Test 1 min on the zone and watch the tap.
What you find Likely cause
Skipped for rain Rain skipping is on. See Rain and weather
Skipped for wet soil The zone’s soil sensor read at or above its level. See Soil sensors
Skipped, “paused until” a date A rain delay is on. See Seasonal adjust and rain delay
Skipped for a treatment hold A job asked to hold watering after a spray. The zone shows “Hold till”; tap it to clear
Zone shows “Flow alert: paused” A burst or leak alert. See Flow meters and leak alerts
Zone shows “No response” The timer isn’t answering. Check its batteries and the timer hub’s power and Wi-Fi
Test runs but no water The tap is off, or the hose to the timer is off or blocked
No run at all The program is switched off, or the zone isn’t in it. Check the Watering tab

A zone won’t stop, or water is still running

Section titled “A zone won’t stop, or water is still running”
  1. Tap Stop on the zone, or Stop all at the top of Home.
  2. If water still runs, turn the tap off by hand or press the timer’s own button.
  3. Check the timer’s batteries.

Every timer has its own countdown, so it turns off at the end of the run even if the controller stops. If water keeps running with the timer off, the valve may be leaking. See How to tell if a tap timer is stuck on.

The controller was off or restarted at the time, often after a power cut. Check it’s plugged in and on Wi-Fi, then run the program by hand if the garden needs it (Run now on the Watering tab).

  • Check Needs you on Home, or the Right amount? card under Health check > Open on the Watering tab. See Right amount?.
  • Check Seasonal adjust on Home. A low figure left from winter shortens every run.
  • Is Weather adjusting runs? On Home, the Rain line says if runs were lengthened or shortened.
  • Measure the zone with a catch-cup test. A wrong watering rate throws every estimate off.

It needs your address. On Home, if it says it’s waiting for your address, set it with Find my block on the Zones tab.

Sprinklers are weak when zones run together

Section titled “Sprinklers are weak when zones run together”

Change Running together to One at a time, or give each zone the right tap name. See Running together.

The app looks different, or things are missing

Section titled “The app looks different, or things are missing”

You may be in Simple view. Settings > Show > Everything brings it all back. See Simple view.

Tap ↶ Undo in the header. It goes back up to 20 changes. See Undo.

  • On My garden, the controller must show “connected”. “Online” means it synced recently, but remote control isn’t live right now.
  • “offline” means it hasn’t been in touch. Check the controller’s power and your home internet. Watering carries on as scheduled at home.
  • See Remote control.
  • Confirm your email: My garden shows “Please confirm your email.” with Resend the email until you do.
  • Check the Monthly water report box on Account.
  • Check your junk or spam folder.
  • A month with nothing to report sends nothing.

See Email alerts.

Calendar apps refresh subscriptions on their own schedule. Google can take hours. If you made a new link, update it in your calendar app. See Calendar subscription.

Settings > This controller > Restart Groundsman (back in about 15 seconds). If that doesn’t help, Restart Groundsman Hub restarts the whole box (about a minute). Anything watering carries on until its timer’s countdown stops it. See Updates and restart.

Contact your installer, or email Groundsman at hello@groundsman.au.

Groundsman · smart watering and lawn care for Adelaide homes ·hello@groundsman.au